Search Results

Malfunctioning emission controls continue to be a major source of emissions from in-use vehicles. We analyze two sources of data on cars with malfunctioning emissions controls: remote sensing surveys and dynamometer tests of cars in the condition they were received. Our analysis indicates that roughly 8 percent of relatively new (2- to 5-year old), modern technology (fuel-injected) cars have malfunctioning emission controls. There is a wide range in the probability of malfunction of specific models, from zero to over 20 percent. Possible causes of high model-specific malfunction probability are poor initial design and/or manufacture.

Life cycle design (LCD) is a framework for designing product systems which are both economically and ecologically sustainable. Key elements of this framework are systems analysis, multicriteria analysis and multistakeholder participation. This paper illustrates the application of life cycle design for a comparative evaluation of a prototype sand-cast 2.0 l aluminum manifold for the 1995 Ford Contour and a 2.0 l equivalent of the 1.9 l multi-tube brazed aluminum manifold for the 1995 Ford Escort. A life cycle inventory analysis was performed for the intake manifolds by evaluating the energy and wastes in the raw material acquisition, material processing, manufacturing, use and retirement stages. The environmental data for the two manifolds were integrated with life cycle cost and performance data to enhance product design and decision making.

As the federal regulations of on-road engine exhaust emissions become more and more stringent, the exhaust emissions of small utility engines are now under close study and are becoming subject to federal regulations. This paper reports the on-going research on emissions and test procedures for small utility engines at the University of Michigan. A group of small utility engines, selected by the National Fuels and Emissions Laboratory of the U.S. Environmental Protection Agency (EPA), were tested at various air/fuel ratios under steady state and transient operation. Mass rate of emissions of carbon monoxide (CO), carbon dioxide (CO2), total hydrocarbons (HC) and oxides of nitrogen (NOx) were measured using dilute sampling. The lean operation limit of some engines was studied to find a compromise among emissions, engine power, and engine life. Experimental research was also undertaken to study emission control techniques; such as catalytic conversion, air injection, and fuel injection.

The exhaust emissions of off-road and utility engines have recently come under increasingly thorough scrutiny and are now becoming the subject of federal regulations. While the most straightforward emissions guidelines relate to steady-state engine performance, it is well known that duty cycles of many small engines have a transient content and that its significance can vary strongly from application to application. Hence, it is important to examine how measured emissions change when the transient content of a test cycle is varied, and what kinds of steady-state and transient test cycles might realistically imitate operational conditions. These questions have been addressed in an experimental study in which several small two- and four-stroke engines have been tested under steady state and transient cycles. The same tests were also carried out when these engines had been adjusted to operate at leaner air-fuel ratios, as might be required by forthcoming regulations.

Cost reduction, quality improvement, and regulatory compliance are well-recognized competitive issues. Companies must excel along each of these fronts while operating in an environment of rapid and multi-faceted change, limited financial and human capital, and increasing product development time pressure. In addition, consumers are demanding automobiles that provide greater performance, function, and comfort while emitting lower emissions, consuming fewer gallons of gasoline, injuring fewer humans, and requiring fewer dollars to build and purchase. A solution to these seemingly conflicting objectives is to take a systems view of the product and industry. This paper explores the material decision process so that manufacturers, component suppliers, and material providers may better understand the interlocking web of compromises that shape the pursuit of value-added alternatives and avoidance of unprofitable compromises.

A cylindrical combustion bomb with dynamic charging system and electro-hydraulic sampling valve is used to study the effects of turbulence on hydrocarbon (HC) emissions from a quench layer and from artificial crevices. The turbulence level is varied by changing the delay time between induction of combustible charge and ignition. Propane-air mixtures were studied over an initial pressure range of 150 to 500 kPa and equivalence ratios of 0.7 to 1.4. Sampling valve experiments show that quench-layer fuel hydrocarbons are extensively oxidized within 5 ms of flame arrival under laminar conditions and that turbulence further reduces the already low level. Upper limit estimates of the residual wall layer HC concentration show that residual quench layer hydrocarbons are only a small fraction of the exhaust HC emission.

Secondary injection in a diesel engine is defined as the introduction of additional fuel into the combustion chamber after the end of the main injection. It is usually caused by residual pressure waves in the high-pressure pipe line connecting the pump and injector. When these waves exceed the injector opening pressure, secondary injection occurs. Tests revealed that the U.S. Army TACOM single-cylinder engine used in this investigation, fitted with an American Bosch injection system, had secondary injection within the normal engine operating region. The pump spill ports and delivery valve were redesigned to eliminate secondary injection, in accordance with previously reported work. Comparative tests of both the conventional and modified injection systems were run on the same engine, and the effects of secondary injection on engine power, economy, and exhaust emissions were determined.

A theoretical digital simulation of a conventional diesel fuel injection system has been developed. The influence of such factors as wave propagation phenomena, pipe friction, and cavitation are included. The computer results are compared with transient pressures as measured on an actual fuel injection system operated on a test bench. The comparisons show the accuracy and validity of this simulation scheme. Special attention is given to some of the important factors that affect the accuracy of the simulation model. These include the effect of pressure on the fuel bulk modulus and wave speed, the pipe line residual pressure, and the coefficient of discharge of important orifices.

Strain gage instrumented transducers were used to measure the cord loads at a number of locations in several different automotive tires loaded against both flat and cylindrical road wheel surfaces. The two basic types of cord load fluctuation encountered in all automobile tires have been identified from these measurements, and the most severe location for cord load fluctuations has been closely bracketed. By these measurements, it has been possible to show that for each tire definite relations exist between the cord loads induced while running on a cylindrical drum and while running on a flat surface. The maximum cord load fluctuations in a tire are the same for the NBS roadwheel and flat surface when the tire is loaded against the roadwheel with a load of between 85 and 90% of that used on the flat surface.

Cycle-to-cycle variation of pressure is a common problem in all spark-ignition engines. To examine the suspected influence of mixture-motion on this variation, a study was performed in a constant volume cylindrical bomb in which a jet of propane-air mixture was directed at the initial flame kernel. The rate of pressure rise of the jet-influenced combustion was compared to the rate for combustion in a quiescent mixture. The flame area, obtained using a spark schlieren photographic technique, and the calculated combustion rate were correlated with the pressure rate. The major results were: the rate of pressure rise increased approximately linearly with mixture jet velocity; and the width of the mixture-jet had an effect on the rate of pressure rise. A jet profile width slightly greather than the spark-gap produced the highest rate of pressure rise.

THIS paper reports work begun in 1935 at the instigation of the Murray Corp. of America. Methods used in studying the relations between the automobile seat cushion and its function in transporting passengers with greater comfort and less fatigue are described. Constructed for this purpose was a piece of apparatus called the Universal Test Seat, whose dimensions were completely adjustable with arrangements to vary the distribution of the supporting pressure in any manner which seemed most comfortable to the passenger. The authors describe tests made by use of this apparatus, present summaries of some of the results recorded and conclude that, to give the passenger the maximum comfort and least fatigue, the following mechanical objectives should be attained by the cushion: 1. To support the passenger over a large area to get the smallest unit pressure on the flesh; 2.